Air Venturi G6 Hand Pump, 4500 PSI

Good solid pump fills my pcp's faster then the Benjamin I have. the length of hose over the short one on the Benjamin is nice making fill up easier for me.

SS Foster female quick connect which only lasted three fill ups before the ball bearings that fell out which PA replaced within a few days of receiving my request about a replacement good work PA

Can't wax too poetic about an air pump, but I will say this: the G6 is simple to put together, does what it's supposed to do and does it well. I'm using it for a 300 bar fill-up on at Ataman AP16 with nary a problem.

The instructions are simple. Perhaps too simple. The G6 comes with a bag filled with components such as o-rings. As I've since learned online, they're replacement parts. Wasn't sure if there were needed for the initial set up or not. But there's nothing saying where the replacement parts should go even if there is a problem.

When you think everything is tightened down...tighten it some more. (With the exception of the pressure gauge.) Had some initial air leaks that even a quarter turn resolved.

Easy to use. Solid construction. Works 100 times better than Benjamin pump

Nothing

Works fast. Great for a marauder and if you pace yourself an air force condor

Easy to assemble, easy to use, wasn't as difficult to pump as people made it out to be, fills up my AT44 cylinders right quick! Also gives me a nice little workout lol

I'd make the base a bit heavier and sturdier, and the air hose is a bit short. I'd lengthen it and add a catch so it doesn't drag on the ground.

Hatsan is a great brand. Being new to the sport of Air Guns, I'm extremely pleased with my first purchase of a Hastan AT44 Tactical QE. Easy to use, and man does it pack a punch. The next air gun I'm going to purchase will be a Hastan AT-P2 QE Tactical Pellet Pistol, and after that (if I have the cash) a Hatsan Barrage or a Hatsan BullMaster. Love it!

Solid pump. O-ring rebuild kits included. No trying to match up O-rings at the local hardware if one fails on a weekend.

Add a 90 elbow to the gauge so you can see it while pumping. Maybe add another foot length to the hose.

Good solid pump. Filling my .25 Marauder from 2000 back up to 3000 only takes about 75 pumps. It is a bite filling up from empty! Haven't had to rebuild the pump yet, but they do send a couple rebuild kits with the pump.

Longer hose and a better SS Foster female quick connect. The bearings fell out after a dozen fill ups. I tend to believe the Foster issue was do to the hose being short and pulling on an angle when filling the rifle. ADD a 90 elbow on the gauge so you can see it while standing and pumping. Stopping to bend over or to raise the pump up to see the gauge sucks. More stress on the hose and connectors too.

PA was top notch in sending out a new Foster end. But call their number instead of emailing them. They are too busy to play email tag!

nothing

if it would function with out problems and not have to pump a hour for 5 shout in five shots in five minutes

There has to be a better way than paying up to 4 thousand for air compressor

This is a very straight forward air pump. Easy to assemble and use. Contains parts to rebuild and repair when needed.

The instruction booklet could be better.

Buy some teflon tape for some of the connections. While it is easy to use, you will get a work out! I see an air tank and/or a compressor in my future.

4500 psi, comes with all necesssry hardware, extra seals, price is on the lower end.

Nothing

Only comes with female quick disconnect, make dure that is what you need

4500#psi folding feet,SMOOTH!!!! Dead head plug and reseal kit.

Shorter hose, better instructions (for the less mechanically inclined)

Had the AF pump for three years of minimal use, then it failed. Sent it in for rebuild, added moisture trap.....three years later.....FAILED AGAIN! Bought this AV pump recently, and its smoother than the AF ever was. No problems so far. Nice pump.